Which LeakAlertor do I have, the 5000 or the 6000?
• The LeakAlertor 6000 has sensors exiting the enclosure, while the LeakAlertor 5000 does not.
• The 6000 has a hole on the front (right side) of the enclosure to permit access to the reset button.
Why Do I Need the LeakAlertor
Testing the LeakAlertor
Resetting the LeakAlertor
Changing the LeakAlertor Battery
Storing the LeakAlertor
LeakAlertor 6000 Installation
Where is the unit placed for the best performance?
Can the LeakAlertor be put inside of the tank?
No. The LeakAlertor 6000 is designed so that the enclosure hangs outside the tank, with the sensors inside the tank (as shown in the installation video). Only the LeakAlertor Connected and LeakAlertor SmartStop are designed to be inside the toilet tank.
Can I bend the sensors?
Yes, but do so gently. The sensors do not take a lot of effort to bend. When you are adjusting the sensors, hold them between your fingers where they enter the plastic tubing for support with one hand, while you adjust the sensors with your other hand. You may need to adjust/bend the sensors during your initial installation if they are touching each other, the tank sides, or parts inside the toilet. Once the unit is installed, you should not need to make any further adjustments.
LeakAlertor 6000 Operation
My LeakAlertor isn't flashing any lights when I flush the toilet...is this right?
No. The LeakAlertor provides an indication during every flush, even if your toilet is functioning properly. (See the Alerts Chart). If no lights flash at any time during a flush, you can test the LeakAlertor by pressing the reset button. Hold the RESET button until the RED lamp flashes. The unit will then flash all three lamps at once and beep. The unit then flashes just the GREEN lamp one to two times per second for approximately one minute. When the RESET is completed and the YELLOW lamp flashes flush the toilet. If the unit does not flash at all, the battery probably needs to be replaced. (See Battery Replacement Instructions)
How loud is the LeakAlertor?
We describe the audible alert as being louder than the “chirp” you hear when your home’s smoke alarm battery is going bad, but quieter than when the smoke alarm is actually going off. You should be able to clearly hear the LeakAlertor from at least 30 feet away, even if the bathroom door is closed.
What are the wires sticking out of the LeakAlertor?
The wires are actually “sensors” that connect to the circuit board inside the LeakAlertor. As the water rises and falls along the length of the sensors, the LeakAlertor is able to calculate the rate of change of the water height. The proprietary software developed by our engineering team analyzes this information in order to determine if your toilet is leaking, constantly running, or is about to overflow.
A leak was detected…now what?
I just replaced my flapper - do I need to reset my LeakAlertor?
Yes, simply press the reset button.
I just replaced by flapper, and my LeakAlertor is still indicating a leak... why?
Once the reset operation is complete if the LeakAlertor is still indicating a problem, unfortunately you probably still have a leak. We suggest contacting a local plumber to find out the cause.
The RED lamp is flashing, but I used dye tablets and there is no coloring in the bowl... why did the LeakAlertor indicate a leak?
What causes my flapper to leak?
The primary reasons that a flapper might leak:
- The flapper deteriorates over time due to cleaning solvents, repetitive use and/or hard water.
- A small piece of foreign matter may be lodged under the flapper lip.
- The flapper in your toilet may not be the correct make, model, or size.
What should I do if my toilet is leaking or if the flapper is stuck?
Can I move the LeakAlertor to a different toilet?
Although you can transfer the LeakAlertor to different toilets, we recommend placing a LeakAlertor on each toilet in order to maximize the opportunity to detect leaks when they actually occur, as well as identifying wide-open flappers and imminent overflows.
The previous LeakAlertor would go off when I was in the shower or using a hairdryer. Will the new LeakAlertor do the same thing?
No. The LeakAlertor 5000 – the previous generation of LeakAlertor – was designed to detect and analyze water movement inside the toilet tank through translational vibration. This occurs when water moving inside of the tank causes the tank to vibrate slightly, which produces distinct sounds. Unfortunately, hair dryers, bathroom fans, running showers, etc., also produce a lot of sound, which could sometimes lead to a “false positive” indication on the 5000. The LeakAlertor 6000 works in a completely different way. The LeakAlertor 6000 operates by directly measuring the rate of change of the water in the toilet tank, so vibration and sound is never a problem.
How do I stop the LeakAlertor from beeping?
Press and hold the reset button until the red light comes on (solid, not blinking). If you’re working on the toilet we recommend removing the battery until your repairs are completed.
The sensors go into the water...can I receive a shock?
No. The LeakAlertor is completely safe to use and harmless.
Can the unit get wet? What happens if I accidently drop it in the toilet or in the tank?
The LeakAlertor has been designed so that it can be cleaned or even sprayed with water without affecting its operation. If the unit is accidentally dropped in the water, remove the top cover and remove the battery. Leave the unit and battery somewhere safe for 48 hours to allow time for the moisture to evaporate. After 48 hours, install the battery and put the top cover back on. The unit should power up normally and can now be placed back on the toilet.
Do not attempt to dry the unit off with a towel, paper towel, hair dryer, etc. Doing so may damage the product and void the warranty.
Ask the Engineers
Is the LeakAlertor 6000 able to collect information?
Yes, but this is an option. The software operating the LeakAlertor 6000 is very dynamic. It performs a wide range of operations in order to monitor and analyze your toilet’s operation. The LeakAlertor 6000 is designed for use in homes and small businesses, and although it is able to process a large amount of data, the 6000 does not collect or store this information.
Our LeakAlertor Connected series of products, which are currently being developed, will have many of these features, including wireless transmission of data. These products are designed with property managers in mind. The LeakAlertor 6000 Evaluation Units, which provide and display substantial data in real time, are available to property managers, hospitality, and water agency professionals.
What do the Alerts mean?
*DURING the entire flush cycle the LeakAlertor will flash/beep to give you a status indication.
|Continuous Flashes||No problem!||No action required!|
|Flashes (after all other alerts)||Battery is low and needs to be replaced||Replace with a CR2032 battery|
|2 Flashes + 2 Beeps||Toilet has a leak||Repair necessary. Replacing flapper is recommended|
|2 Flashes + 1 long Beep, followed by 2 short Beeps||Faulty fill valve||Replace fill valve (Fluidmaster 400 fill valve is recommended)|
|Continuous Flashes + Beeps||Flapper is stuck open or toilet is about to overflow||Shut off water to toilet immediately!! (Alerts don’t stop until problem is corrected, reset button is hit, or LeakAlertor battery dies).|
LeakAlertor® 6000 Battery Replacement Instructions
Be sure to check out the 1 Minute Video Instructions
Press the reset button to place the unit into the RESET mode, then remove unit from the tank.
Remove the back of the enclosure by lightly pressing a screwdriver or butter knife through the front slot. Remove the board from the enclosure. (Do not use the sensors to pull the board out of the enclosure!)
Remove the old battery with a toothpick and slide the new battery into place with the “+” side facing UP. (The unit will automatically go into RESET mode.)
Place the board back into the enclosure. Reattach the back so the circular notch faces inward and to the left.
Place the unit back onto the toilet, and replace the tank lid.
DCN: LA6KBRI 03/16
LeakAlertor 6000 Guides
LA 6000 User's Guide
Battery Replacement Guide
LA 6000 Evaluator's Guide
LA 6000 Leave-Behind Brochure
LA 6000 7 Reasons & 5 Reasons
5 Reasons Why Dye Tabs Are Ineffective
5 Reasons why dye tablets are ineffective